Answer:In general, the system will auto-download the APP in background after installing Realtek Audio driver. Please type 'Sound Blaster Connect” in Win10 search bar to access APP.

If the APP doesn't show up on your system, please follow the steps below to install it manually. 1.Make sure your motherboard supports Creative Sound and with Realtek Audio driver installed. Please visit motherboard specification page on www.ASRock.com for details. Realtek Audio driver could be installed/downloaded from support CD and ASRock official website. 2.Access 'Sound Blaster Connect” on Microsoft Store and click 'Get” to start downloading. 3.After installation, click Launch to launch the APP. Please refer to the following table which supports the Creative SoundBlaster Cinema5.

Platform Models Intel Fatal1ty H370 Performance Fatal1ty B360 Gaming K4 Fatal1ty B360M Performance Z390 Phantom Gaming 9 Z390 Phantom Gaming 6 Z390 Phantom Gaming SLI-ITX/ac AMD Fatal1ty X470 Gaming K4 Fatal1ty X470 Gaming-ITX/ac Fatal1ty B450 Gaming-ITX/ac Fatal1ty B450 Gaming K4 X399 Phantom Gaming 6. Answer:In general, the system will auto-download the APP in background after installing Realtek Audio driver. Please type 'Realtek Audio Console” in Win10 search bar to access APP.Please connect the LAN cable when installing the Realtek Audio driver.

If the APP doesn't show up on your system, please follow the steps below to install it manually. 1.Go to the device manager to check if the Reaktek Audio driver is installed. Realtek Audio driver could be installed / downloaded from support CD and ASRock official website: www.ASRock.com. 2.Please refer to the following link to access 'Realtek Audio Control” on Microsoft Store and click 'Get” to start downloading.

3.After installation, click Launch to launch the APP. Answer:Please follow the steps below 1. Refer to the 'Microsoft Windows Mixed Reality PC hardware guidelines” to check the system hardware requirement.The Windows Mixed Reality requires Integrated Intel HD Graphics 620 or greater DX12-capable integrated GPU. If an external graphics card is installed, please enable 'IGPU Multi-Monitor” under BIOS. BIOS Path: Advanced Chipset Configuration IGPU Multi-Monitor 3. Download the VGA driver version 15.

From the Intel download center and Install it on your system. Download Link: 4.

Install the 'Windows Mixed Reality Headset” USB 3.0 connector to the on-board USB3.0 port. Install the 'Windows Mixed Reality Headset” HDMI connector to the on-board HDMI port The Windows Mixed Reality Headset should work now. Answer:Please refer to the following requirements, configurations and setup procedures. Requirements OS: Windows 10 Receiver / decoder: Onkyo TX-NR 747 or other receiver supporting HDCP 2.2 Player: Pioneer Ultra HD Blu-ray drive BD Disk: Most 3D / 4K BD disk movie Playback Software: Power DVD 14 or later version Configuration M/B: Z270 Gaming-ITX/ac BIOS: P2.30 Setup 1. When the system boots up, press 'F2' to enter UEFI setup screen. Go to Advanced CPU Configuration and enable 'Software Guard Extensions' in BIOS setting.

Press 'F10' to save and exit the BIOS setup screen. Boot into O.S. Install all drivers for the M/B. Install ME driver ver: 11.6.0.1126 (supports Ultra HD Blu-ray). Download the driver from the following link: 3.

Go to Control Panel Hardware and sound Sound and select 'Receiver output”. Answer:Requirements: O/S: Windows 10 Receiver / decoder: Onkyo TX-NR 747 or other receiver supports HDCP 2.2 Playback Software: Power DVD 14 (from Pioneer Ultra HD Blu-ray Drive) Configuration: M/B: Z270 Gaming-ITX/ac BIOS: P1.20 Setup: 1.

When the system boots up, press 'F2” to enter UEFI setup screen. Go to Advanced CPU Configuration and enable 'Software Guard Extensions” in BIOS setting. Press 'F10” to save and exit the BIOS setup screen. Boot into O/S. Install all drivers for the M/B.

Install ME driver (v11.6.0.1126SWMSI). Download the driver from the following link: 3. Go to Control Panel Hardware and sound Sound and select 'HDMI output”. Enable the 'UHD color” on the TV.

Please run 'Ultra Blu-ray advisor” to see if all 'Pass”. Pioneer UHDBD Advisor: 5.

Asrock Sound Driver Download

Put a 4K movie BD disc into the Pioneer Ultra HD Blu-ray drive. Click 'Power DVD”.

Then you can play the content. Answer:Requirements: O/S: Windows 10 Receiver / decoder: Onkyo TX-NR 747 or other receiver supports HDCP 2.2 Playback Software: Power DVD 14 (from Pioneer Ultra HD Blu-ray Drive) Configuration: M/B: Z170 Gaming-ITX/AC BIOS: P7.10 CPU: 7th generation Intel® Core™ i7/i5 processor for Desktop PC (Kaby Lake-S) Setup: 1. Please connect the HDMI cable to HDMI2 port of Z170 Gaming-ITX/ac. When the system boots up, press 'F2” to enter UEFI setup screen. Go to Advanced CPU Configuration and enable 'Software Guard Extensions” in BIOS setting. Press 'F10” to save and exit the BIOS setup screen. Boot into O/S.

Install all drivers for the M/B. Install ME driver(v11.6.0.1126SWMSI). Download the driver from the following link: 4. Please enter Control Panel Hardware and sound Sound. Select 'HDMI output” 5.

Enable the 'UHD color” on the TV. Please run 'Ultra Blu-ray advisor” to see if all 'Pass”. Pioneer UHDBD Advisor: 6. Due to the fact that HDR is not supported by Intel 100 series chipset, please disable ”UHD color” from TV. Put a 4K movie BD disc into the Pioneer Ultra HD Blu-ray drive. Click ' Power DVD”.

Then you can play the content. Answer:Since AMD AM4 is a new structure and we just found BIOS cannot be completely updated by our Instant Flash. Thus, for the old BIOS version released before 2017/03/07, there is no 'Instant Flash” option under BIOS. To make sure BIOS update can be executed completely, please use DOS or Windows BIOS update methods to do update temporarily. After updating to the following version, Instant Flash functions and options are supported under BIOS and it can be used for updating the newer BIOS file in the future. Model BIOS Version Fatal1ty X370 Professional Gaming P1.50 X370 Taichi P1.50 X370 Killer SLI/ac P1.60 X370 Killer SLI P1.60 Fatal1ty X370 Gaming K4 P1.60 Fatal1ty AB350 Gaming K4 P1.40 AB350 Pro4 P1.40 AB350M P1.20.

Answer:Please follow below steps to update the ASM1074 firmware: ※This FW Update Tool can only be used on Intel Braswell platform, with Windows 7 64bit / Windows 10 64bit. Run the tool as Administrator. Please make sure there's no device connected to the ASM1074 hub, and then press 'Yes” to execute updating. The F/W update is processing.

After the process finished, please restart the system. Please shut down the system, and unplug the AC power cord for 3 minutes. The firmware update process is finished. ※If the update process tool stops during updating as below, do the followings. Please press 'OK” and follow the message to restart the system and then try again.

You will see a message as below: 2. Please press 'OK”, the system will start to update the firmware again.

(It's normal that the 'update version” is 0e) 3. After it's finished, please restart the system. Please shut down the system, and then unplug the AC power cord for 3 minutes. The firmware updating process is finished. Answer:Please refer to the steps below to install the VGA driver with Windows update. Right click 'This PC' to enter 'Manage'.

Choose 'Device Manager' on the left; enter 'Display adapters' then right click on 'Microsoft Basic Display Adapter' and then select 'Update Driver Software' (Please make sure the system is connected to the Internet) Step3. The system will update the driver via Internet automatically. Wait till it displays Windows has successfully updated your driver software.

After this driver update, the Device Manager should be able to recognize your VGA adapter. Answer:Please refer to the following link to download and install Windows 10 Home 64-bit on Beebox. After installing the OS, follow the steps below to activate Windows 10 Home 64-bit. Download the 'AsrProductKey' tool. Unzip the tool and launch it. You will receive the product key of your system as shown below.

Type 'Activation' on Windows search and press enter. Click 'Change Product Key' and enter the key which was displayed at step3. After entering the Product Key, the OS will be activated. Answer:If you've updated the Killer LAN driver from version 1.1.52.1451 to newer versions under Windows 10 x86/x64, it might cause the LAN driver to malfunction. Please follow the steps below to fix this problem.

Step 1: Open Device Manager and uninstall the Killer LAN driver. Step 2: Select the checkbox and press OK. Step 3: Scan for hardware changes. Step 4: Execute the new Killer LAN driver 1.1.54.1506 or newer versions and press Remove then restart the system. Step 5: Install the new Killer LAN driver and then restart the system. Answer:For Intel G3258 CPUs to support Windows 10, please download the following BIOS or later versions with Microcode 19 from the download links on our website. If your model isn't listed in the table, please visit the beta zone of your model and then update the latest beta BIOS.

Model P BIOS H81M-VG4 R2.0 P1.40 H81M-DGS R2.0 P1.60 H81M-HDS R2.0 P1.30 H81M-HDS P2.10 H81M-DG4 P1.10 H97 Anniversary P1.50 H97M Anniversary P2.10 B85 Anniversary P1.40 B95M-DGS P1.60 B85M-DGS P1.50 B85M Pro3 P1.40 H97M Pro4 P2.00 B85M-HDS P1.70 B85 Pro4 P2.30 B85M P2.50 H81M-HG4 P1.50 H81M P1.90 H81M-GL P2.00 H81M-G P1.40 H97 Pro4 P1.90 H97M P2.00. Answer:Step 1: Please make sure that you have installed the latest BIOS and two 1866MHz or higher frequency memory modules in dual channel. Also keep the default UEFI setting of 'Dual Graphics' option on Auto. BIOS download link: Step 2: Install one AMD RADEON PCI Express graphics card to the PCIE slot. Step 3: Connect the monitor cable to the onboard VGA port. Please note that the current VGA driver / VBIOS allows Dual Graphics output from the onboard display only. For any future update, please refer to our website for further information.

Step 4: Boot into the OS. Then please remove the AMD driver if you have any VGA driver installed in your system. Step 5: Install the onboard VGA driver from our support CD to your system for both the onboard VGA and the discrete graphics card. Step 6: Restart your computer.

Right-click the desktop. Click 'AMD VISION Engine Control Center' to enter AMD VISION Engine Control Center.

Step 7: You can also click 'AMD VISION Engine Control Center' on your Windows taskbar to enter AMD VISION Engine Control Center. Step 8: In AMD VISION Engine Control Center, please choose 'Performance'. Click 'AMD CrossFire™'. Step 9: Click 'Enable CrossFire™' and click 'Apply' to save your change. Step 10: Reboot your system.

Then you can freely enjoy the benefit of Dual Graphics feature. Answer:There are various possibilities that cause this issue, please refer to the following suggestions to check your system. Please make sure your HDDs' SATA power cable and SATA cable are connected with the motherboard. Enter the BIOS setup screen, scroll to the advanced page and enter Storage Configuration, set SATA mode to IDE. If you want to install Windows XP under AHCI mode, due to Windows XP requirements, you'll need to pre-install the SATA driver first, please refer to the following FAQ for further details.

If you have already tried the suggestions above, please change your SATA cables or SATA ports for verification. Answer:Please follow below SOP to install Windows Vista/7 64bit OS on the RAID volume: Step 1: Flash BIOS to latest version. Step 2: Connect all HDDs then do below settings: Set SATA Mode as RAID Mode Change Onboard RAID 3TB+ Unlocker to EFI Compatible ROM The options are located in BIOS Advanced Storage Configuration Then press F10 to save settings. Step 3: Press F11 during boot up and choose boot to Built-in EFI Shell.

Step 4: Key in 'drvcfg', and you will see the information like below: Drv4E CtrlB5 Langeng Step 5: Key in 'dh Drv number', for example: key in 'dh 4E'. Step 6: Key in 'drvcfg –s Drv number Ctrl number' to enter Raid Utility. For example: key in 'drvcfg –s 4E B5' Step 7: Choose Logical Drive Main Menu to set up Raid Drive.

Step 8: Choose Logical Drive Create Menu to create a Raid Drive. Step 9: Choose Usable Physical Drive List to select Raid HDD. Step 10: Press Space on keyboard to toggle checkbox. Step11: Choose Ld Size setting, and key in the Raid size.

Step12: After set up Raid size, please click Start to Create Step13: Press 'F10' to Exit Utility. Step14: During reboot, please press 'F11' to enter Boot Menu. Choose UEFI: CD/DVD Drive. This option only shows on Windows7 64bit and Vista 64bit OS.

Step 15: Follow Windows Installation Guide to install OS. Please load latest SATA RAID driver ver.3.3.1540.22 during OS installation from our website Step 16: Install latest drivers from ASRock website. Answer:For support Intel next generation 22nm CPU, it required correspond BIOS version, drivers, and AXTU update. Please follow below steps to update correspond BIOS, drivers and Utilities. Step 1: Check BIOS version. Please check below table and update BIOS since or higher version.

If you have the same or a higher BIOS version on your motherboard, there is no need to update the BIOS and you can skip step 2. Answer: Requirements: OS: Windows7, Vista SP2 or later. Receiver / decoder: Onkyo TX-SR608 amplifier for example: Playback software: for example Power DVD10 v10.0.2025.52 or other playback software. Please install all drivers from support CD, after that please check device manager, there should be no any '!' Please enter Control Panel Hardware and Sound Sound, If you would like to output via HDMI, please select HDMI output If you would like to output via SPDI, please select Digital output.Different motherboard/chipset may show different information, above picture is for references only. Enter the Audio settings in your application.

We take Power DVD 10 here for example: Choose the Speaker environment and Output modes as you want. Set your decoder/amplifier to the digital sound output, which you want. Set the correct output format on your content /source manual. Then you can play the content/source. Answer:Step1: Step2: Please unzip the SATA RAID driver which downloaded in Step1 and put the SATA RAID driver in USB flash drive.

Step3: Please click 'Load Driver' when selecting hard drive in Windows installation. Step4: Click 'Browse' Step5: Choose the folder downloaded in Step1. RSTef6iaStorA2008R232 is used for 32-bit operating system. RSTef6iaStorA2008R264 is used for 64-bit operating system Step6: Select the SATA RAID driver for 'Intel(R) C600 Series.' As below picture and click next to install the OS. Please connect the USB front panel cable to CIR1 and USB 67 header.

The pin header mark in red is required to connect. The properly connecting USB front panel cable with CIR header as below picture. Step2: Please connect CIR receiver to USB front panel before booting up system. Step3: Enter BIOS setting screen and make sure the CIR controller is setting at Enabled (Advanced - Super IO Configuration – CIR Controller - Enabled) (If you didn't see the CIR Controller option in BIOS, please shut down your system and plug CIR receiver to another USB port on front panel then try again) Step4: Enter Windows, Execute ASRock support CD and install CIR Driver (it would be listed at the bottom of driver list) Note: Please connect the CIR receiver to USB front panel before you boot up system. Answer:Since the user account security level setting under Windows ® 7 64-bit. After you update the Marvell driver and Utility to new version, this dialog box will not show up as before. Please follow the steps as below to update Marvell driver and Utility.

Please uninstall Marvell driver and RAID utility which has installed on your system. Please download and update Marvell driver and Utility by following link. Marvell SATA3 driver ver:1.0.0.1051 download link: Marvell RAID Utility ver:4.1.0.1909 download link.

Answer:If you use AC'97 front audio panel, please install it to the HD audio header as below: A. Connect MicIN (MIC) to MIC2L. Connect AudioR (RIN) to OUT2R and AudioL (LIN) to OUT2L. Connect Ground (GND) to Ground (GND). MICRET and OUTRET are for HD audio panel only.

You don't need to connect them for AC'97 audio panel. Enter BIOS Setup Utility. Enter Advanced Settings, and then select Chipset Configuration. Set the Front Panel Control option from Auto to Enabled. For Windows ® XP F.

Enter Windows ® system. Click the icon on the lower right hand taskbar to enter VIA ® ADeck. Click 'Mixer', select 'Front Microphones', choose 'Front Mic Boost', and leave. Like below picture: H. If you want to hear your voice through Front Mic, Please click 'Mixer', select 'Play Back', choose 'Front Mic', and leave. Like below picture: For Windows ® Vista™ / Windows ® 7 F. Enter BIOS 'Chipset Settings' page, manual Front Panel to Enable.

Enter Windows ® system. Click the icon on the lower right hand taskbar to enter VIA ® VDeck. Click 'Front Mic', select 'Default Device' H. If you want to hear your voice through Front Mic, Please click 'Speaker Output' icon. Like below picture.

Answer:Please refer our website for windows7 support list. Website link: If your models are not listed on Windows ® 7 support list, please kindly try inbox driver first. Or go to chipset vender website to download the chipset driver. Intel ® website: AMD ® website: NVIDIA ® website: Realtek website: VIA ® website: If you got any further issues, please contact ASRock TSD: AsrockTSD@asrock.com.tw. Answer:Some suggestions as below may solve the issue, 1.

Please re-install your Windows ® XP and install required driver in such order: a. HD Audio Driver and Application(VIA ® HD Audio driver) b. Onboard HDMI HD driver (NVIDIA ® HDMI driver) c. All in 1 driver. Refering to the attached picture, please install a display driver in support CD - Others - Display - XP32185.66 - Setup.exe 3.

Please check your VGA driver version has been update to 6. By device management. Since when ever you plugged the rear speaker to ION330, the sound playback would AUTOMATICALLY set to 'HD Audio Rear Output', therefore, during the test, please ONLY connect HDMI to the TV, and make sure the sound playback is set to 'NVIDIA ® HD Audio'. Answer:ION330 can support Dolby Digital 5.1, DTS 5.1 and LPCM 7.1 only under Windows ® Vista™ or later version.

Please refer to below steps to setting your system. Please update the HOTFIX: KB959458 or update your Vista Service Package to SP2. Hotfix download link: 2.

Install the drivers in the order listed as below a. VIA ® HD Audio Driver 7100d b. NVIDIA ® HD Audio driver 1.0.0.51 c. NVIDIA ® nForce All in 1 v20.14 3. Install a proper AP, we used PowerDVD 9.0 for tests here. Enter Control Panel - Sound - Configure to choose Stereo, 5.1. Enter Control Panel - Sound - Properties to set the sampling rate, Max Fs.

For Dolby-Digital DTS is 48 KHz. RIGHT CLICK in PowerDVD - Settings - Audio a. Speaker Environment - Use HDMI (Current Vista Setting) b.

Output Mode - Non-Decoded DD/DTS to external device. RIGHT CLICK in PowerDVD - Settings - Video. Enable Hardware Acceleration 8. As you can see in the picture below, the audio output is Dolby Digital 5.1.If you want to output DTS 5.1, please select it in audio menu of DVD.For your information, the source of the test is a DVD which supports both DD5.1 and DTS 5.1. Answer:Following steps as below may help you to solve this issue. If your motherboard has the SLI/XFire switch card, please put the SLI/XFire Switch card to 8x/8x, if there is no switch card on your motherboard, please skip this step.

Remove the graphics card from the PCI-E 1 slot. Restart Windows.

Install the driver for the graphics card (again). Put the VGA card back into the PCI-E 1 slot, and put the SLI bridge on. Activate SLI function by NVIDIA ® control panel. Or please download the latest VGA driver from NVIDIA ® Web Site and try the new driver. Answer:Please refer to the steps as below to solve the issue. 1.Please download a registry from the link as below, For Asia: For EU: ftp://europe.asrock.com/drivers/others/NVUSBS3.zip For US: ftp://www.asrock.com/drivers/others/NVUSBS3.zip 2.Referring to the picture, please double click on the file NVUSBS3, and click YES. After the registry is complete, a window may shows up, please press OK and RESTART your computer.

3.Referring to the picture, double click on Keyboard and Mouse in START - Control Panel. 4.Referring to the picture, move to Hardware tags as 1. And 3., click on Properties as 2. 5.Referring to the picture, move to Power Management tag as 1. Check Allow this device to bring the computer out of standby in BOTH Keyboard and Mouse windows, as 2.

6.Now it's available for you to bring your computer from S3 and S4 with your USB keyboard and mouse. Answer:Due to the NVIDIA ® chipset specification, the HDD driver is requirement, please install the HDD driver during the installation of operating system. Please refer to below steps to install the HDD driver: 1. Please download the driver and save the driver to floppy disk, USB driver, CD or DVD.

Asrock Audio Driver Windows 10

HDD driver download link: 2. Click 'Load driver' icon at the 'Where do you want to install Windows?' Then click 'OK' 4. Check the icon and click 'Brows' 5. Then choose the driver from the source which you saved. Select the HDD driver and click 'Next' to install the driver. Answer:Due to the operating system limitation, Windows ® XP only supports MBR disk format, the MBR disk format cannot support the hard drive capacity over 2TB.

If you want to use over 2TB RAID volume to be your boot disk, below three conditions must be required: 1.Your operating system must be Windows ® Vista™ x64 SP1 or Windows ® 7 64bit. 3.GPT disk format. Please refer to following link to get more information.

Link: http://www.microsoft.com/whdc/device/storage/GPTFAQ.mspx. Answer:Please refer to below steps to reinstall Realtek HD Audio driver: 1.Enter into 'Add or Remove Programs' and remove 'Realtek High Definition Audio Driver' 2.Disable all 'Microsoft ® UAA Bus Driver for High Definition Audio' in Device Manager first 3.Then uninstall all 'Microsoft ® UAA Bus Driver for High Definition Audio' from the system. 4.Reboot system 5.Reinstall 'Realtek HD Audio driver' from Motherboard Support CD. If you still meet this problem, please reinstall fresh Windows ® system. Answer:Please refer to below suggestions.

If you want to install the Windows ® Vista™ with non-RAID mode: Install the SATA driver v998 from support CD during the installation of Windows ® Vista™. The driver path in support CD is Support CD/Drivers/ SATA2/ nVIDIA/ Vista64Vista(112)/ IDE/ WinVista/ sataide. Step1: Step2: Step3: You can also download the SATA driver v998 from ASRock website and save it to a floppy diskette, USB flash drive or CD/DVD disk. Then install the SATA driver v998 from floppy diskette, USB flash drive or CD/DVD disk during the installation of Windows ® Vista™.

ALiveNF6P-VSTA: ALiveNF6G-VSTA: ALiveNF6G-GLAN: ALiveNF6G-DVI: AM2NF6G-VSTA: If you want to install the Windows ® Vista™ with RAID mode: Please refer to the NVIDIA RAID installation guide. Answer:Please refer to following steps to install Microsoft ® Vista Hot Fix KB929777 to fix this problem. Only install 2GB memory to the motherboard first. Install Microsoft ® Vista Hot Fix KB929777 Microsoft ® Hot Fix KB929777 is available at:. After the Hot Fix installation is completed, please restart the Windows ® Vista™ 64-bit system. Shutdown the system and install 4GB memories back to the motherboard.Now, the system should work fine with 4GB memory.

Answer:This is a known issue of Windows ® Vista™ 64 bit. Please install the following two hotfixes from Microsoft. It will solve this problem. Please install the Hotfixes according to the following steps: 1.Boot into Windows ® Vista™ 64bit with less than3GB system memory. (If you are not able to finish installing Windows ® Vista™ 64bit, please install Windows ® Vista™ with less than 3GB system memory) 2.Install the first hotfix, reboot, and then install the second. 3.Reboot the system and let system go into Windows ® Vista™ 64bit.

4.Shut down the computer. And then install the Memory back. Answer:Yes, ALiveNF7G-HD720P/ALiveNF7G-HDready supports HDMI output. However, a DVI to HDMI cable or adapter is required. DVI to HDMI cable DVI to HDMI Connector Besides the DVI to HDMI cable/adapter, please also do the following settings in BIOS SETUP and Windows ® Vista™/Vista 64-bit: 1.In BIOS SETUP, go to 'Advanced'-'Chipset Configuration', and set the option 'Onboard HDMI HD Audio' to Auto. 2.Under Windows ® Vista™/Vista 64-bit, go to 'Sound' settings and select the Digital Output Device (SPDIF) as a playback device.

You can find more detail information in user manual page 13. Answer:Please refer to below steps to set the audio device.

1.Install Realtek HD Audio driver from motherboard Support CD. Or download the Realtek HD audio driver from ASRock website. 2.Plug in your recording devices (Microphone or other devices) to the Line-in port (or Microphone port), and then the recording device will show up 'Line In' (or 'Microphone') icon. Please kindly refer to below image. (Control Panel Sound Recording).Before plug in the recording devices:.After plug in the recording devices: 3.Reopen the Sound Recorder to record the audio.

Answer:First, your hardware must meet the requirements of the Windows ® Vista™ Premium system. If not, you may not enable Windows ® Aero.

Windows ® Vista™ Premium system - Hardware Minimum Requirements Item Requirements CPU x86-compatible 32-bit CPU or x64-compatible 64-bit CPU Memory 512MB Single Channel (Premium, Discrete models) 512MB x 2 Dual Channel (Premium, embedded models) VGA DirectX9.0 (with WDDM Driver) with 128bit VGA memory (Premium) Audio UAA Audio (HD Audio, USB Audio and IEEE1394 Audio) (Premium or Basic depends on Codec Vista logo level) Second, please kindly refer to below steps to enable Windows ® Aero feature: 1.Press right button of mouse at Desktop and click 'Personalize'. 2.Enter into 'Windows ® Color and Appearance' setting 3.Refer to below image to enter 'Open classic appearance properties for more color options' setting.

4.Set 'Color scheme' as 'Windows ® Aero'. Answer:If you encounter this problem, there are two solutions you can choose, pls. Select either one at your convenience. Solution1 Please flash BIOS to P1.70 or later for AM2NF6G-VSTA and P1.60 or later for ALiveNF6G-DVI. Or please refer following steps to re-write MAC address under Windows ® Vista™. Step1: Check MAC address.

When system boot up, press 'F2' to enter BIOS setting. Boot- 'Boot settings Configuration' - set 'Boot From Onboard LAN' to 'enable'. System will restart. Please 'F11' and select 'NVIDIA Boot Agent'. Then you will see MAC address, pls.

Record it with no space for later usage. Step2: Boot system into Window Vista Right click 'Computer' and click 'Properties' Step3: Click 'Device Manager' Step4: Click 'Continue' Step5. Right click 'Networking Controller' and click 'Properties'.

Step6: Choose 'Network Address' in 'Advanced ' folder. Write 'MAC Address' which got from step1 into Value item. Then click 'OK'. Answer:1.If your CD is IVD12/ IVD12b (775Dual-VSTA), AV890-10 (ALiveSATA2-GLAN) or AV31/ AV31b (AM2V890-VSTA), you will get the issue. Please execute the 'Setup.exe' file from following directory of support CD. 775Dual-VISTA- IVD12 CD Drivers Audio REALTEK MCEXP2K (R1.36) 775Dual-VISTA-IVD12b CD Drivers Audio/ REALTEK MCEXP2K (R1.41) ALiveSATA2-GLAN - AV890-10 CD Drivers Audio REALTEK MCEXP2K (R1.39) AM2V890-VSTA - AV31/ AV31b CD Drivers Audio REALTEK MCEXP2K (R1.39) 2:The yellow exclamation mark in Device Manager is unnecessary.

It will not affect the system at all. Please follow below steps to remove it.

Right-click 'My Computer' on your desktop, and click 'Properties'. Select 'Hardware', and click 'Device Manager'.

In 'Device Manager', double-click the option 'System Devices'. You will find 'VIA ® Standard PCI to PCIE Bridge' item with a yellow exclamation mark. Right-click 'VIA ® Standard PCI to PCIE Bridge', and select 'Uninstall'. Confirm your choice by clicking 'OK'.

After a few seconds, click 'Scan for hardware changes' icon on the top. Answer:Please refer to following steps to fix this problem. Please set the 'DRAM Frequency' as '333MHz (DDRII 667)' in BIOS setup if you use DDRII 667 RAM.

(BIOS/ Advanced/ Chipset Configuration/ DRAM Frequency). Please enable the 'Flexibility Option' in BIOS setup if you use DDRII 533 RAM. (BIOS/ Advanced/ Chipset Configuration/ Flexibility Option). If the problem still remains, please update the BIOS to P1.80 or later version.

Answer:You need to make a SATA driver diskette before you start the OS installation. Please refer to the following steps:.

Enter 'SATA Operation Mode' in BIOS setup to set the option to RAID. Insert the ASRock Support CD into your optical drive to boot your system. During POST at the beginning of system boot-up, press key, and then a window for boot devices selection appears. Please select CDROM as the boot device.

When you see the message on the screen, 'Do you want to generate Serial ATA driver diskette YN?' . Then you will see these messages, Please insert a diskette into the floppy drive.

Asrock Audio Driver Windows 7

Formatting the floppy diskette will lose ALL data in it! Start to format and copy files YN?

Please insert a floppy diskette into the floppy drive, and press. The system will start to format the floppy diskette and copy SATA drivers into the floppy diskette. Restart and enter 'SATA Operation Mode' in BIOS setup to set the option to AHCI.

At the beginning of Windows ® setup, press F6 to install a third-party SCSI or RAID driver. When prompted, insert a floppy disk containing the ULi ® RAID driver. After reading the floppy disk, the driver will be presented. Select the driver to install according to the mode you choose and the OS you install.

Answer:In order to enable Intel ® Matrix Storage Manager, please refer to the following steps:. Enter into BIOS to set your SATA hard disk in AHCI mode or RAID mode. (BIOS-Advance-IDE Configuration -Configure SATA as- AHCI or RAID ).

Make a SATA driver diskette with support CD before installing your system. Please press 'F6' to load Intel ® SATA driver during operating system setup.

Please refer to Setting Up a 'RAID Ready' System of User Manual of Support CD. Information Manual User ). Install the SATA2 Driver from support CD after the installation of Windows ® 2000 / Windows ® XP / Windows ® XP 64-bit OS.